Anti Corrosive LED Light Fitting 1800mm Supplier 

What is an Anti-Corrosive LED Light Fitting 1800mm?

Key Technical Specifications and Features

An Anti corrosive LED light fitting 1800mm—commercially referred to across the UK electrical sector as a 6ft weatherproof LED batten or vapor-proof linear luminaire—is our largest and most powerful solid-state linear lighting solution. Purpose-built to act as a straight replacement for aging, high-energy 6-foot fluorescent T8 or T5 tube fittings, this 1800mm series is available in standard 34W and ultra-high-output 68W configurations. Operating on a stable AC 220-240V voltage spectrum, each unit combines advanced SMD LED arrays with a high-efficiency isolated driver to ensure uniform, flicker-free task illumination across expansive footprints.

Anti corrosive LED light fitting 1800mm

Understanding IP65 and IP66 Weatherproof Ratings

Engineered specifically to survive inside tough environments, this linear pac enclosure carries a verified IP65 Ingress Protection rating (with IP66 options available upon project contract request):

  • Dust Protection (6): Complete immunity to dust, airborne debris, and fine particulate matter, preventing internal contamination over decades of service.

  • Water Resistant Armor (5/6): Guarantees the break-resistant housing blocks low-pressure water jets and heavy splashing from any directional angle, keeping the internal electronics safe during intensive commercial wash-downs.

The Benefits of 6ft (1800mm) Polycarbonate Construction

Manufactured to compete directly against premium spec profiles like the Aurora LinearPac or Bell Dura LED series, our 1800mm fitting is built with an injection-molded polycarbonate body paired with a high-efficiency prismatic polycarbonate diffuser. Polycarbonate possesses extreme impact resistance, meaning it will not rust, warp, fade, or tarnish under constant chemical exposure or physical impacts. The entire assembly is sealed tightly using heavy-duty marine-grade stainless steel fixing clips, ensuring a permanent airtight seal that outlasts cheaper ABS alternatives.

Technical Specifications

Electrical & Operational

  • Model Codes: MX483B-LD34W-1800 / MX483B-LD68W-1800

  • Input Voltage: AC 220-240V, 50/60Hz

  • Driver Technology: High-efficiency isolated driver

  • Circuit Protections: Integrated low-voltage protection device

  • Operating Temp: -20°C to +40°C

  • Flicker Metrics: Flicker-free operation for peak visual comfort

  • Compliance: Full CE & RoHS Certified tracking

Optical & Mechanical

  • Power Options: 34W (Standard) | 68W (Ultra-Output)

  • Luminous Flux: 4,760 lm (34W) | 9,520 lm (68W)

  • Dimensions Size: 1870 x96 x78

  • Base Material: Injection-molded impact polycarbonate

  • Diffuser Type: High-efficiency prismatic PC diffuser

  • Color Temperature: 4000K Cool White (Standard) / 6000K Daylight

  • Mounting Kits: Surface mounted clips included

Key Advantages of 1800mm Anti-Corrosive LED Battens

Energy Efficiency and High Lumen Output

By delivering an exceptional system efficiency, our 68W double batten equivalent yields a massive 9,520 lumens of balanced light. Upgrading to this solid-state technology enables commercial facility managers to realize energy savings of up to 50% to 60% compared to traditional fluorescent fittings, which draw excessive power due to magnetic ballast losses.

Durable Protection Against Water, Dust, and Impact

The robust polycarbonate shell combined with an airtight gasket structure blocks water jets, sand dust, and moisture completely. This makes it an ideal fit for hostile indoor and covered outdoor installation sites where standard commercial linear profiles would short-circuit or degrade.

Long Lifespan and Low Maintenance Costs

Operating with premium high-density chip arrays and optimized thermal management, this 1800mm series provides an extended operational lifespan. Eliminating recurring trade labor costs for lamp swap-outs, starter replacements, and ballast troubleshooting saves significant overhead for large-scale operations.

Available Types and Configurations of 1800mm LED Battens

Standard Non-Corrosive LED Fittings

The base configuration for everyday industrial environments, wired directly for 230V mains voltage grids. These fixtures feature rapid-install internal terminal blocks and spacious rear entries for straight wiring setups.

Emergency Backup LED Anti-Corrosive Lights

Equipped upon project request with an integrated 3-hour emergency luminaire backup battery pack. In the event of a facility power failure, the internal intelligent inverter activates immediately to maintain safe, code-compliant illumination along municipal escape paths.

Microwave Sensor and Motion-Activated Variants

For maximum energy management, integrated microwave motion sensors provide automated occupancy detection. These controls automatically dim the 6ft LED strip light down to safe standby levels during zero-occupancy windows, scaling up to full brightness instantly when movement is detected.

Single vs. Twin (Double) LED Batten Outputs

  • Single Output (34W / 4,760 lm): Designed for medium height lines ($2.8\text – 3.5\text$), narrow utility aisles, and storage corridors requiring balanced ambient lighting.

  • Twin Double Batten (68W / 9,520 lm): Features an expanded chassis layout holding dual rows of high-density chips. Purpose-built for high-clearance applications where maximum down-lumens are required.

Common Applications for 6ft Anti-Corrosive Lighting

Industrial, Warehouse, and Factory Lighting

Perfect for large-scale industrial manufacturing floors, logistics hubs, sorting yards, and packaging plants where constant machinery vibration and heavy dust accumulation prevent the use of standard fixtures.

Car Parks, Garages, and Outdoor Spaces

The ideal specification for underground car parks, multi-story parking structures, covered loading bays, and mechanical vehicle repair garages. Its rugged casing easily resists the corrosive effects of automotive exhaust soot and moisture pooling.

Commercial Kitchens and Tough Environments

Optimized for commercial food preparation environments, walk-in cold stores, and industrial wash bays. The smooth, non-corrosive polycarbonate body handles chemical sanitization and direct water spraying with zero deterioration.

How to Choose the Right 1800mm Anti-Corrosive LED Fitting

Selecting the Correct Colour Temperature (CCT)

  • 4000K (Cool White): The standard recommendation for large commercial offices, processing factories, and industrial warehouses, offering a crisp environment that enhances safety and visual comfort.

  • 6000K (Daylight): Best for high-precision manufacturing, textile inspection lines, and commercial auto-body garages demanding sharp, high-contrast focus.

Power Selectable and Wattage Options

When engineering large multi-zone tenders, selecting the right wattage is critical. Use the standard 34W model for low-clearance walkways and transition zones. Scale up to the 68W high-output model for mounting points above 4 meters to ensure crisp horizontal lux levels across your production floor.

Legislation, Compliance, and Installation Safety

Our entire industrial batten series is fully CE and RoHS certified, ensuring compliance with strict European installation standards. Each 1800mm chassis features integrated backplane mounting slots that allow it to mount directly onto an existing BESA box or standard surface masonry conduits, reducing field installation time for electrical contractors.